NUCLEAR PLANT SIMULATION CODE
NUCLEAR PLANT SIMULATION SIMULATOR
NUCLEAR PLANT SIMULATION FREE

This is an hobby so I suspect it will take ages to finish this project.Р”Р„lso, not quite sure that I'm on the right track.Since RELAP5 code has general and advanced features in thermal-hydraulic computation, it has been widely used in transient and accident safety analysis, experiment planning analysis, and system simulation, etc. After, youРІР‚в„ўll have to control everything togetherРІР‚В¦Р”В¬oding in HaxeFlixel and using Gimp for pixel-art. 1st day coal silos, 2nd day valveРІР‚в„ўs controls and 3rd day the coal rate into the boiler.

Tutorial levels РІР‚вЂњ On the first 3 levels (work days) you will be attending just a specific part of the plant.

Upgrades РІР‚вЂњ You will start with slower valves, slow start/stop time pumps and mills, low capacity silos, etcРІР‚В¦ As you complete game levels you will earn credits that you can spend in upgrades (and maintenance).

Maintenance team РІР‚вЂњ If you have sufficient workers in the maintenance team youРІР‚в„ўll to repair it during the level at a quicker pace.

If not, the change of fault will rise to the point off failure. You will be doing it, at a cost, between levels/shifts (working day).

Fault handling РІР‚вЂњ Each part starts to degrade and so youРІР‚в„ўll be wise to maintain it.

NUCLEAR PLANT SIMULATION FREE

Once it gets there, you are free to increase/decrease coal rate at the remaining mills to achieve the desired power rate. Wait until pressure builds up to 150 bar (green mark at drum panel, pressure dial)Р”РЃ. Increase rate of mill n1 (M1) to ~20% (2nd mark on the upper dial next to M1 on/off knob)Р”В§. Turn on automatics (steam, feedwater and hotwell)Р”В¦. Turn on coal mills (turn each mill knob to green position)Р”Тђ. Check silos levels (~80%) a bit high (that ok to start)Р”Сћ. hot-well valve auto РІР‚вЂњ that keeps hot-well at 50%.Р”РЋ.feedwater valve auto РІР‚вЂњ that keeps drum level at 50%,.steam valve auto РІР‚вЂњ that keeps pressure at 150 bar,.To help you itРІР‚в„ўll be available some automatic controls (youРІР‚в„ўll have to РІР‚СљbuyРІР‚Сњ them later in the game РІР‚вЂњ not clear): Be careful no the fill them too much and it take some time for the feeder to stopРІР‚В¦ You can fill in the silo by (1) selecting the silo (1st knob form the left at the silos panel) and turn on the silo feeder (2nd knob from the left at the silos panel). You must maintain, the hotwell level 50% is the operating level) by opening/closing the hotwell valve and with, at least, one hotwell pump on.Р”Р„lso, as you feed water to the drum, you must watch the feedwater tank level (50% is the operating level) that depends on the РІР‚СљbalanceРІР‚Сњ of water inflow from the hotwell and water outflow feeding the drum.Р”Р„s you burn coal your coal siloРІР‚в„ўs level drop and so you much also maintain the desired silo level. To sustain the drum level, you must feed water into the drum by opening/closing the feedwater valve and with, at least, one feedwater pump on.Р”Р„s your power plant generates, the steam that goes through the turbines ends up at the condenser, turning from steam to liquid, filling the hot well. To sustain the pressure in the drum you must control the rate of coal thatРІР‚в„ўs burned in the boiler. The correct levels are 150 bar for drum pressure and 50% for drum level. The power rate is controlled by opening/closing the steam valve, the delivers the steam to the steam turbines hence rotating the shaft thatРІР‚в„ўs connect to the power generator.Р”Р„s you open/close the steam valve pressure and water level decreases/increases. To ensure that plant is operating between acceptable levels (green marks in the dials) at each power rate. steam, feedwater and hot-well valves (regulate water/steam flow).the drum, hot-well and feedwater tank levels.coal rate into the boiler (trough coal mills),.I thought in making each level corresponding to working day/shift, with repair/upgrade possibility for several parts, on the after-shift debriefing screen, but isnРІР‚в„ўt clear if thatРІР‚в„ўs the way to goРІР‚В¦ The objective of the game is to maintain a specific power rate during a specific amount of time (not implemented yet) coping with part faultРІР‚в„ўs and maintaining everything working properly (thereРІР‚в„ўll be warnings/signals to help you).

NUCLEAR PLANT SIMULATION SIMULATOR

It's intended to be a power station simulator but at simpler level. The РІР‚СљrotationРІР‚Сњ of the shaft РІР‚СљproducesРІР‚Сњ electricity. The РІР‚СљprocessРІР‚Сњ of generating power in a thermal power station is РІР‚Сљvery simpleРІР‚Сњ РІР‚вЂњ heat water to steam, then drive it through a steam turbine which shaft is connect to a power generator.

So I decided to make a power plant simulator (kind off.) I like power plants РІР‚В¦ especially thermal power plants.

Nuclear plant simulation